rhopoint components ltd email: components@rhopoint.co.uk website: www.rhopoint.co.uk coto technology hh hh h ighigh ighigh igh p p p p p erformanceerformance erformanceerformance erformance sip r sip r sip r sip r sip r eedeed eedeed eed r r r r r elayselays elayselays elays the sip relay is the industry standard when high reliability and consistent performance are desired in a compact package. the 9001 and 9002 are high performance relays ideally suited for automatic test equipment, instrumentation, rf, and telecommunications applications. the 9091 is a compact version of the 9001. it offers many of the same features of the larger package while using 40% less board space. the specification tables allow you to select the appropriate relay for your application. ss ss s erieseries erieseries eries f f f f f eatureseatures eatureseatures eatures u high insulation resistance - 10 12 w minimum. (10 13 w typical) high reliability, hermetically sealed contacts for long life. tested to 1 billion operations. high dielectric strength available, consult factory. high speed switching compared to electromechanical relays. molded thermoset body on integral lead frame design. coaxial shield for 50 w impedance and switching of fast rise time digital pulses - 9002 only. optional coil suppression diode - protects coil drive circuits. ul file # e-67117, csa file # lr 28537 9000 series / molded sip reed relays model 9001 model 9002 model 9091 dimensions in inches (millimeters) 30 o
coto technology rhopoint components ltd holland rd, hurst green, oxted, surrey, rh8 9ax,engl a n d m od e l number 90 01 90 02 90 91 parameters tes t condi ti on s units 4 pi n sip 6 pi n sip 1 for m a coil specs. nom. coil voltage vdc 5 12 5 12 5 12 max. coil voltage vdc 6.5 15.0 6.5 15.0 6.5 15.0 coil resistance +/- 10%, 25 c w 500 1000 350 750 500 1000 operate voltage must operate by vdc - max. 3.75 9.0 3.75 9.0 3.75 9.0 release voltage must release by vdc - min. 0.4 1.0 0.4 1.0 0.4 1.0 contact ratings switching voltage max dc/peak ac resist. volts 200 2 00 200 switching current max dc/peak ac resist. amps 0.5 0 .5 0.5 carry current max dc/peak ac resist. amps 1.5 1 .5 1.5 contact rating max dc/peak ac resist. watts 1 0 10 1 0 life expectancy-typical 1 signal level 1.0v, 1.0ma x 10 6 ops. 1000 1000 500 static contact resistance (max. init.) 50mv, 10ma w 0.150 0 .150 0.125 dynamic contact resistance ( max. init. ) 0.5v, 50ma at 100 hz, 1.5 msec w 0.200 0 .200 0.150 relay specifications insulation resistance (minimum) between all isolated pins at 100v, 25c, 40% rh w x 10 12 x 10 12 x 10 12 capacitance - typical across open contacts no shield shield floating shield guarding pf pf pf 0.7 - - - 0.8 0.1 0.1 - - open contact to coil no shield shield floating shield guarding pf pf pf 1.4 - - - 1.4 0.5 2.0 - - contact to shield contacts open, shield floating pf - 1 .4 - dielectric strength (minimum) between contacts contacts to shield contacts/shield to coil vdc/peak ac vdc/peak ac vdc/peak ac 300 - 1500 300 1500 1500 200 - 1500 operate time - including bounce - typical at nominal coil voltage, 30 hz square wave msec. 0.35 0.35 0.50 release time - typical zener-diode suppression 4 diode suppression msec. 0.10 - 0.10 - 0.30 0.12 notes: 1 consult factory for life expectancy at other switching loads. 9090 series contact resistance >0.5w defines end of life or failure to open. 2 optional diode is connected to pin #2 (+) and pin #3(-). correct coil polarity must be observed. 3 9000 series part numbers designated with form b contacts, these relays contain bias magnets. correct coil polarity must be observed. 4 consists of 20v zener-diode and 1n1002 diode in series, connected in parallel with coil. 9000 series / molded sip reed relays environmental ratings storage temp: - 35c to + 100c; operating temp: - 20c to + 85c solder temp: 270c max; 10 sec. max the operate and release voltage and the coil resistance are specified at 25c. these values vary by approximately 0.4%/c as the ambient temperature varies. vibration: 20 gs to 2000 hz; shock: 50 gs top view: dot stamped on relay refers to pin #1 grid = .1"x.1" (2.54mm x 2.54mm) 2 22
|
